0 items
 
800-229-0009
952-556-5666

Challenge* Style

Challenge* Style

Challenge* Style

Challenge* Style

Showing 1 - 20 of 71 « First < Previous 1 2 3 4 Next > Last »

BOOK TRIMMING GUIDE CHALLENGE

PART # CH5-7-M361
Sign in to see pricing or create an account.

"Challenge" style spine clamp or book clamp for use on the guillotine paper cutter back gauge. These spine clamps keep books and other stitched booklets flat for accurate and square cutting.  They are very effective at...

DRILL BLOCK CHALLENGE 1-1/2 x 3/4 ROUND 1 DOZEN

PART # CBLOCKS1.5
Sign in to see pricing or create an account.

CBLOCKS1.5    is a round, Challenge wood block that is 1 ½” (dia.) X ¾” (thick) and comes in a pack of 1 dozen. Maple wood blocks are the perfect drilling accessory. The properties of maple make it the...

DRILL BLOCK CHALLENGE 2-1/2 x 3/4 ROUND 1 DOZEN

PART # CBLOCKS2.5
Sign in to see pricing or create an account.

CBLOCKS2.5    is a round, Challenge wood block that is 2 ½” (dia.) X ¾” (thick) and comes in a pack of 1 dozen. Maple wood blocks are the perfect drilling accessory. The properties of maple make it the...

DRILL BLOCK CHALLENGE 3 x 3/4 ROUND 1 DOZEN

PART # CBLOCKS3
Sign in to see pricing or create an account.

CBLOCKS3  is a round, Challenge wood block that is 3” (dia.) X ¾” (thick) and comes in a pack of 1 dozen. Maple wood blocks are the perfect drilling accessory. The properties of maple make it the perfect hardness for...

CHALLENGE MDL TRIMMER THREE KNIFE SET

CHALLENGE MDL TRIMMER THREE KNIFE SET

Choose from three different grades of steel. Only sold in set of three knives.

CHALLENGE SHARPENER WITHOUT REAMER

PART # CSHARP
Sign in to see pricing or create an account.

Product  CSHARP  is a Challenge style hand-held tube sharpener. Reamer not included. Accepts 3/8" reamer shaft.

Challenge Standard Steel

Challenge Standard Steel

Standard steel is made from economy grade carbon tool steel.

CHALLENGE CMT 330 THREE KNIFE SET

CHALLENGE CMT 330 THREE KNIFE SET

Choose from two types of High Speed Steel. Only sold in a set of three.

CHALLENGE BACK GAUGE TAPE WHEEL (56P-25)

PART # WH333
Sign in to see pricing or create an account.

Challenge Back Gauge Tape Measure Wheel or Tape Wheel Assembly (56P-25, 56P25)   This all new machined aluminum wheel or pulley acts as a guide for the front and back ends of the steel back gauge tape measure.  This is...

CHALLENGE DRILL DRIFT REMOVER

PART # 4687
Sign in to see pricing or create an account.

CHALLENGE DRILL HEAD

PART # DRILL HEAD-C
Sign in to see pricing or create an account.

CHALLENGE KNIFE CHANGING HANDLE

PART # H63
Sign in to see pricing or create an account.

Knife Changing Handle for Challenge Paper Cutters and for some of the Baumfolder Guillotine Cutters.  Length : 4-5/8" long (machined from one solid piece of bar stock). The knurled handle section is 5/8"...

DRILL BLOCK CHALLENGE 6 x 1-1/4 x 3/8 END GRAIN 3 DOZEN

PART # CBLOCKSO
Sign in to see pricing or create an account.

CBLOCKSO  is a rectangular, Challenge wood block that is 6” X 1 ¼” X 3/8” and comes in a pack of 3 dozen. Maple wood blocks are the perfect drilling accessory. The properties of maple make it the perfect hardness...

DRILL BLOCK CHALLENGE 6 x 1-1/4 x 3/8 LONG GRAIN 3 DOZEN

PART # CBLOCKSOL
Sign in to see pricing or create an account.

CBLOCKSOL  is a rectangular, Challenge wood block that is 6” X 1 ¼” X 3/8” and comes in a pack of 3 dozen. Maple wood blocks are the perfect drilling accessory. The properties of maple make it the perfect...

CARBIDE REAMER 3 FLUTE 3/8" SHAFT

PART # CAR-REAMER3
Sign in to see pricing or create an account.

This reamer has three flutes and a 3/8" shaft. It is used with the hand-held sharpeners.

PAPER DRILL SHARPENER WITH REAMER SPINNET

PART # MS-1
Sign in to see pricing or create an account.

This sharpener is used with Spinnet and Challenge style drill bits. It works with bits from 1/8" to 1/2."

CARBIDE REAMER MULTI-FLUTE FOR MS-1 SHARPENER

PART # MS1-06
Sign in to see pricing or create an account.

The MS1-06 is used with the MS-1 sharpener. It has multiple flutes and a 1/4" shaft.

Challenge High Speed Steel Knives

Challenge High Speed Steel Knives

Our standard high speed steel knives will be an excellent addition to your Challenge cutter. It's T1 inlay will provide you with a long cutting lifespan.

CHALLENGE, LAWSON, SEYBOLD KNIFE CHANGING HANDLE

PART # H64-12
Sign in to see pricing or create an account.

Knife Changing Handle for Challenge/Lawson/Seybol d Paper Cutters, including the Challenge Diamond cutter models and the Challenge F Series cutters. This solid steel handle is 6-1/4" long. The 7/8" diameter shank is knurled...

HELICAL GEAR COVER

PART # 6598-2
Sign in to see pricing or create an account.

Showing 1 - 20 of 71 « First < Previous 1 2 3 4 Next > Last »